New 350-401 Test Materials & Valid 350-401 Test Engine
350-401 Updated Exam Dumps [2022] Practice Valid Exam Dumps Question
Most Suitable Exam Candidates
The Cisco 350-401 exam targets IT specialists with a minimum of 3-5 years of proven experience in managing enterprise networking technologies. It suits all individuals looking to broaden their IT knowledge or get into more advanced positions within the IT niche. In a nutshell, the following groups would benefit from this training:
- Network Administrators
- Help desk technicians.
- Enterprise Network Engineers;
- System Engineers;
- System Administrators;
Automation (15%)
- Describing the high-level principles and benefits of the Yet Another Next Generation (YANG) language;
- Comparing the agentless vs. agent orchestration tools, such as SaltStack, Chef, Ansible, and Puppet;
- Constructing the EEM applet to automate data collection, troubleshooting, or configuration.
- Constructing the valid file utilizing the JSON code;
- Describing APIs for vManage and Cisco DNA Center;
- Interpreting the results in payload and REST API response codes with the usage of RESTCONF and Cisco DNA Center;
- Interpreting the basic Python components and scripts;
What Are the Details of the Cisco ENCOR 300-401 Certification Exam?
Even though the vendor doesn't give details on the total number of questions that the test includes, there is still some information disclosed. Thus, candidates should be ready to solve questions of multiple formats such as drag and drop, scenario-based, multiple-choice, or multiple-answer items. One will need to answer correctly about 80 to 85% of the total exam questions in 120 minutes.
ENCOR test is available in Japanese and English. The registration fee is of $300. When it comes to the enrollment process, candidates will have to follow four simple steps. They will first need to create an account on the Pearson VUE platform and log in. The next step would be to go to the “proctored exam” section. The third action involves searching for the test's code which is 350-401. Finally, they will need to follow the instructions that appear on the screen and finalize the registration.
NEW QUESTION 96
Refer to the exhibit. Which command is required to verify NETCONF capability reply messages?
- A. show netconf rpc-reply
- B. show netconf schema | section rpc-reply
- C. show netconf | section rpc-reply
- D. show netconf xml rpc-reply
Answer: C
NEW QUESTION 97
Based on this interface configuration, what is the expected state of OSPF adjacency?
- A. Full on both routers
- B. not established
- C. FULL/BDR on R1 and FULL/BDR on R2
- D. 2WAY/DROTHER on both routers
Answer: B
NEW QUESTION 98
Refer to exhibit.
VLANs 50 and 60 exist on the trunk links between all switches All access ports on SW3 are configured for VLAN 50 and SW1 is the VTP server Which command ensures that SW3 receives frames only from VLAN
50?
- A. SW1 (config)#vtp pruning
- B. SW2(config)#vtp pruning
- C. SW1 (config)#vtp mode transparent
- D. SW3(config)#vtp mode transparent
Answer: A
NEW QUESTION 99
Based on the output below, which Python code shows the value of the "upTime" key?
A)
B)
C)
D)
- A. Option D
- B. Option B
- C. Option A
- D. Option C
Answer: A
NEW QUESTION 100
A company plans to implement intent-based networking in its campus infrastructure. Which design facilities a migrate from a traditional campus design to a programmer fabric designer?
- A. Layer 2 access
- B. routed access
- C. two-tier
- D. three-tier
Answer: C
Explanation:
Explanation
Intent-based Networking (IBN) transforms a hardware-centric, manual network into a controller-led network that captures business intent and translates it into policies that can be automated and applied consistently across the network. The goal is for the network to continuously monitor and adjust network performance to help assure desired business outcomes. IBN builds on software-defined networking (SDN). SDN usually uses spine-leaf architecture, which is typically deployed as two layers: spines (such as an aggregation layer), and leaves (such as an access layer).
The example below shows the usage of lock command:
def demo(host, user, names):
With manager. Connect(host=host, port=22, username=user) as m:
With m.locked(target='running'):
for n in names:
m.edit_config (target='running', config=template % n)
The command "m.locked (target='running')" causes a lock to be acquired on the running datastore.
NEW QUESTION 101
Refer to the exhibit.
An engineer must ensure that all traffic leaving AS 200 will choose Link 2 as the exit point. Assuming that all BGP neighbor relationships have been formed and that the attributes have not been changed on any of the routers, which configuration accomplish task?
- A. R4(config-router)nighbor 10.2.2.2 weight 200
- B. R3(config-router)bgp default local-preference 200
- C. R3(config-router)neighbor 10.1.1.1 weight 200
- D. R4(config-router)bgp default local-preference 200
Answer: D
Explanation:
Reference:
Local preference is an indication to the AS about which path has preference to exit the AS in order to reach a certain network. A path with a higher local preference is preferred. The default value for local preference is 100.
Unlike the weight attribute, which is only relevant to the local router, local preference is an attribute that routers exchange in the same AS. The local preference is set with the "bgp default local-preference value" command.
In this case, both R3 & R4 have exit links but R4 has higher local-preference so R4
NEW QUESTION 102
Which tool is used in Cisco DNA Center to build generic configurations that are able to be applied on device with similar network settings?
- A. Command Runner
- B. Authentication Template
- C. Template Editor
- D. Application Policies
Answer: C
Explanation:
Explanation
Cisco DNA Center provides an interactive editor called Template Editor to author CLI templates. Template Editor is a centralized CLI management tool to help design a set of device configurations that you need to build devices in a branch. When you have a site, office, or branch that uses a similar set of devices and configurations, you can use Template Editor to build generic configurations and apply the configurations to one or more devices in the branch.
Reference: https://www.cisco.com/c/en/us/td/docs/cloud-systemsmanagement/network-automation-and-management/dna-center/1-3/user_guide/b_cisco_dna_center_ug_1_3/b_cisco_dna_center_ug_1_3_chapter_0111.html
NEW QUESTION 103 
Refer to the exhibit How was spanning-tree configured on this interface?
- A. By entering the command spanning-tree vlan 10,20,30,40 root primary in the interface configuration mode
- B. By entering the command spanning-tree portfast in the interface configuration mode
- C. By entering the command spanning-tree mst1 vlan 10,20,30,40 in the global configuration mode
- D. By entering the command spanning-tree portfast trunk in the interface configuration mode.
Answer: D
NEW QUESTION 104
A GRE tunnel is down with the error message %TUN-5-RECUR DOWN:
Which two options describe possible causes of the error? (Choose two)
- A. There is link flapping on the tunnel
- B. The tunnel destination is being routed out of the tunnel interface
- C. Incorrect destination IP addresses are configured on the tunnel
- D. There is instability in the network due to route flapping
- E. The tunnel mode and tunnel IP address are misconfigured
Answer: B,D
Explanation:
Explanation
The %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing error message means that the generic routing encapsulation (GRE) tunnel router has discovered a recursive routing problem. This condition is usually due to one of these causes:
+ A misconfiguration that causes the router to try to route to the tunnel destination address using the tunnel interface itself (recursive routing)
+ A temporary instability caused by route flapping elsewhere in the network
NEW QUESTION 105
Refer to the exhibit.
Which password allows access to line con 0 for a username of "tommy" under normal operation?
- A. Tommy
- B. 0 Cisco
- C. local
- D. Cisco
Answer: D
Explanation:
Explanation
https://www.cisco.com/c/en/us/support/docs/security-vpn/terminal-access-controller-access-control-system-tacac
NEW QUESTION 106
Drag and drop the QoS mechanisms from the left onto their descriptions on the right
Answer:
Explanation:
Explanation
NEW QUESTION 107
Drag the drop the description from the left onto the routing protocol they describe on the right.
Answer:
Explanation:
Explanation:
Unlike OSPF where we can summarize only on ABR or ASBR, in EIGRP we can summarize anywhere. Manual summarization can be applied anywhere in EIGRP domain, on every router, on every interface via the ip summary-address eigrp asnumber address mask [administrative-distance] command (for example: ip summary-address eigrp 1 192.168.16.0 255.255.248.0). Summary route will exist in routing table as long as at least one more specific route will exist. If the last specific route will disappear, summary route also will fade out. The metric used by EIGRP manual summary route is the minimum metric of the specific routes.
NEW QUESTION 108
Refer to the exhibit.
Which configuration change ensures that R1 is the active gateway whenever it is in a functional state for the 172.30.110.0/24 network?
- A. Option D
- B. Option B
- C. Option A
- D. Option C
Answer: A
NEW QUESTION 109
Which antenna type should be used for a site-to-site wireless connection?
- A. patch
- B. Omnidirectional
- C. dipole
- D. Yagi
Answer: D
NEW QUESTION 110
A client device fails to see the enterprise SSID, but other devices are connected to it. What is the cause of this issue?
- A. The hidden SSID was not manually configured on the client.
- B. The broadcast SSID was not manually configured on the client.
- C. The client has incorrect credentials stored for the configured hidden SSID.
- D. The client has incorrect credentials stored for the configured broadcast SSID.
Answer: A
NEW QUESTION 111
Which two mechanisms are available to secure NTP? (Choose two.)
- A. TACACS-based authentication
- B. IP prefix list-based
- C. Encrypted authentication
- D. IP access list-based
- E. IPsec
Answer: C,D
Explanation:
Explanation
The time kept on a machine is a critical resource and it is strongly recommend that you use the security features of NTP to avoid the accidental or malicious setting of incorrect time. The two security features available are an access list-based restriction scheme and an encrypted authentication mechanism.
Reference: https://www.cisco.com/c/en/us/support/docs/availability/high-availability/19643- ntpm.html
NEW QUESTION 112
Refer to the exhibit.
Which command must be applied to R2 for an OSPF neighborship to form?
- A. network 20.1.1.2.0.0.0.0 area 0
- B. network 20.1.1.2 255.255.255 area 0
- C. network 20.1.1.2 255.255.0.0. area 0
- D. network 20.1.1.2.0.0.255.255 area 0
Answer: A
Explanation:
Explanation
The network 20.0.0.0 0.0.0.255 area 0 command on R2 did not cover the IP address of Fa1/1 interface of R2 so OSPF did not run on this interface. Therefore we have to use the command network 20.1.1.2 0.0.255.255 area 0 to turn on OSPF on this interface.
Note: The command network 20.1.1.2 0.0.255.255 area 0 can be used too so this answer is also correct but answer C is the best answer here.
The network 0.0.0.0 255.255.255.255 area 0 command on R1 will run OSPF on all active
NEW QUESTION 113
How are the different versions of IGMP compatible?
- A. IGMPv3 is compatible only with IGMPv3.
- B. IGMPv2 is compatible only with IGMPv1.
- C. IGMPv3 is compatible only with IGMPv1
- D. IGMPv2 is compatible only with IGMPv2.
Answer: B
NEW QUESTION 114
Which exhibit displays a valid JSON file?
- A. Option D
- B. Option B
- C. Option A
- D. Option C
Answer: A
NEW QUESTION 115
Drag and drop the LIPS components on the left to the correct description on the right.
Answer:
Explanation:
NEW QUESTION 116
Drag and drop the characteristics from the left onto the protocols they apply to on the right?
Answer:
Explanation:
NEW QUESTION 117
Based on this interface configuration, what is the expected state of OSPF adjacency?
- A. Full on both routers
- B. not established
- C. FULL/BDR on R1 and FULL/BDR on R2
- D. 2WAY/DROTHER on both routers
Answer: B
NEW QUESTION 118
Drag and drop the characteristics from the left onto the routing protocols they describe on the right.
Answer:
Explanation:
Explanation
A picture containing timeline Description automatically generated
NEW QUESTION 119
Refer to the exhibit.
Which IP address becomes the active next hop for 192.168.102 0/24 when 192.168.101.2 fails?
- A. 192.168.101.6
- B. 192.168.101.18
- C. 192.168.101.10
- D. 192.168.101.14
Answer: B
Explanation:
Explanation
The '>' shown in the output above indicates that the path with a next hop of 192.168.101.2 is the current best path.
Path Selection Attributes: Weight > Local Preference > Originate > AS Path > Origin > MED > External > IGP Cost > eBGP Peering > Router ID BGP prefers the path with highest weight but the weights here are all 0 (which indicate all routes that are not originated by the local router) so we need to check the Local Preference. Answer
'192.168.101.18' path without LOCAL_PREF (LocPrf column) means it has the default value of 100.
Therefore we can find the two next best paths with the next hop of 192.168.101.18 and
192.168.101.10.
We have to move to the next path selection attribute: Originate. BGP prefers the path that the local router originated (which is indicated with the "next hop 0.0.0.0"). But none of the two best paths is self-originated.
The AS Path of the next hop 192.168.101.18 is shorter than the AS Path of the next hop
192.168.101.10 then the next hop 192.168.101.18 will be chosen as the next best path.
NEW QUESTION 120
......
350-401 Sample with Accurate & Updated Questions: https://www.examsreviews.com/350-401-pass4sure-exam-review.html
350-401 Exam Info and Free Practice Test | ExamsReviews: https://drive.google.com/open?id=17iYpjLiVhqKVcmP1X1dsKT621wJ5nGxi