Practice on 2026 LATEST NACE-CIP1-001 Exam Updated 100 Questions
Download Latest NACE-CIP1-001 Dumps with Authentic Real Exam QA's
NEW QUESTION # 25
Fine cracks in the surface of a coating that rarely reach the substrate are called
- A. blistering.
- B. cracking.
- C. alligatoring.
- D. checking.
Answer: D
NEW QUESTION # 26
Check abrasive blast pressure close to the
- A. compressor
- B. substrate
- C. blast nozzle
- D. blast pot
Answer: C
NEW QUESTION # 27
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:
- A. Low Surface Temperature
- B. High Surface Temperature
- C. Low Relative Humidity
- D. High Relative Humidity
Answer: C
NEW QUESTION # 28
Polymerization is the process of:
- A. Monomers joining together
- B. Monomers telegraphing
- C. All organic coatings
- D. All thermoplastic coatings
Answer: A
NEW QUESTION # 29
Daily reports are important because:
Select All That Apply
- A. Inspectors rarely change on a project.
- B. Management uses them to make personnel decisions.
- C. The information aids communication with supervisors.
- D. the information impacts future projects.
Answer: B,C,D
NEW QUESTION # 30
It is good practice for the NACE Inspector to have instrument calibration certificates available:
- A. In the office only
- B. At all times
- C. Only if the specification requires it
- D. In the field only
Answer: B
NEW QUESTION # 31
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?
- A. 6.35 cm (2.5 inch)
- B. 1 cm (.39 inch)
- C. 2.5 millimeters (.10 inch)
- D. 2.5 cm (1 inch)
Answer: D
NEW QUESTION # 32
You ate the NACE Inspector on a job where NACE No. 2/SSPC - SP 10 has been specified. You are finding the Contractor is leaving mill scale on the on surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mill scale to remain and still be in be in compliance with the standard.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Permit coating to take place so as not to lose the blast
- C. Review the relevant standard with the Contractor
- D. Shut the job down
Answer: C
NEW QUESTION # 33
When applying Thermal Spray Coatings the specification is most likely to refence:
- A. SSPC PA 2
- B. NACE SP 0188
- C. NACE SP 0178
- D. SSPC-CS 23.00/AWS C2.23/NACE No. 12
Answer: D
NEW QUESTION # 34
Which one of the following documents is the best source for coating technical data:
- A. Application Guidelines
- B. Specification
- C. Safety Data Sheet;
- D. Technical Data Sheet
Answer: D
NEW QUESTION # 35
Excessive working of the surface with a power grinder can be detrimental because excessive burnishing
- A. scratches the surface too deeply resulting in uneven coating application
- B. develops a polished surface, which is a poor anchor profile for most coatings
- C. develops a good anchor profile resulting in uneven coating application.
- D. damages structural elements thereby speeding up the corrosion process.
Answer: B
NEW QUESTION # 36
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Advise the Contractor he cannot proceed
- B. Call your supervisor
- C. Advise the Contractor of your readings
- D. Advise the Contractor he can proceed
Answer: C
NEW QUESTION # 37
According to SSPC PA 2 a Spot Measurement is:
- A. The average of gauge readings taken in a 4cm (1.5 inch) circle
- B. A single gauge reading
- C. The overall average of all readings
- D. The average of all spot measurements in a given area
Answer: A
NEW QUESTION # 38
Upon arrival of coating materials, the inspector should
- A. observe and document time frame and environmental conditions between each coat.
- B. observe aryl document that the applicator WFT at regular intervals during application.
- C. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.
- D. observe and document the amount of material and batch numbers.
Answer: D
NEW QUESTION # 39
Silicone coatings are typically:
- A. Applied in very' thin films
- B. Used strictly in immersion service
- C. Used as a sacrificial primer
- D. Applied in very thick films
Answer: A
NEW QUESTION # 40
NACE SP 0178 is a standard for:
- A. Tanks and Vessels to be Externally Coated
- B. Tanks and Vessels to, be Lined for Immersion Service
- C. Structural steel to be coated for Atmospheric Service
- D. Stainless steel pipe to be Externally Coated
Answer: B
NEW QUESTION # 41
ASTM Standards are applicable:
- A. When specified
- B. In North America
- C. In the USA
- D. In Asia
Answer: A
NEW QUESTION # 42
......
Authentic NACE-CIP1-001 Exam Dumps PDF - Aug-2026 Updated: https://www.examsreviews.com/NACE-CIP1-001-pass4sure-exam-review.html
NACE-CIP1-001 Dumps Special Discount for limited time Try FOR FREE: https://drive.google.com/open?id=1yqlgx_AOqB7A4dILkouSVzfplbsUsHYK